CompositesWorld
Issue link: https://cw.epubxp.com/i/532917
JULY 2015 26 CompositesWorld FEATURE / MOLDMAKING TECHNOLOGY SIDE STORY Holding fxtures, jigs, trim tools and metal-forming dies can be expensive elements of post-mold composite part processing and assembly. Designing and building such tools can be an expensive and time-consuming part of the production process in its own right. Additive manufacturing, therefore, is proving especially useful in this area. One application is in the post-mold trimming of similar but not identical series-molded parts. Aurora Flight Sciences (Manassas, VA, US), for example, recently produced a series of female bulkhead tools, 3D-printed in polycarbonate, for a UAV demonstrator. "We've pulled about six parts from the bulkhead tools so far," says project engineer Dan Cottrell. David Dahl, an application engineer for AM supplier Stratasys (Eden Prairie, MN, US), explains that AM enabled successful production of the bulkhead parts: "Traditional metal tools typically are designed with scribe lines machined into the surface that transfer to the composite parts, and guide post-cure trimming operations. But you can't really print a scribe line on an AM tool." Because each bulkhead is shaped slightly diferently, parts made on the same tool end up with diferent dimensions because they're trimmed uniquely. Cottrell says that to save time during trimming and fnishing, Stratasys simply printed lightweight trim tools (router templates) for each bulkhead version, in a matter of a few days, to expedite the trimming process (see photo at left). "We were able to generate an entire tooling family, very economically," he adds. Mike Vander Wel, head of equipment and tool engineering for Boeing Commercial Airplanes (Seattle, WA, US), describes another application: the use of AM to build a drill jig for an older aircraft part. Because legacy aircraft — US Air Force tankers, for example — were built before digital engineering tools were available, it can be time consuming to develop a mold, or holding fxture, for a replacement part. "If we had made this drill jig in metal, it would have cost at least $50,000," he says. Instead, the part that required replacement was laser scanned, which captured the part dimensions in a CAD fle that could be easily transferred to the 3D printer. A holding jig was then 3D-printed using a low-cost plastic polymer within a few days. The jig enabled support and fast drilling of the metal replacement part. "This is a great example of how we can justify the cost of placing and using 3D printers in our facilities in a matter of months," adds Vander Wel. Robert "Yogi" Kestler, Science & Technology (S&T;) lead; Robert Thompson, a materials engineer; and Douglas Greenwood, an aerospace engineer, at FRC East (Cherry Point, NC, US), the maintenance, repair and overhaul center for all US Navy and Marine Corps vertical-lift aircraft, tell of a set of 3D-printed fxtures used to repair a damaged AV-8B Harrier 3D-printed fxtures & jigs jet, which lost its front landing gear during a fight from the aircraft carrier USS Bataan. To safely land, the pilot had to descend vertically and place the aircraft's nose cone onto a padded cradle, which substituted for the inoperative gear. All went well until the last moment, when the plane bounced, damaging an internal metal frame within the nose. After damage assessment, repair planning and structural analysis, Kestler's group received the CAD solid model of the frame on a Wednesday, began 3D printing the next day, and on Friday, tooling blocks were complete. Greenwood explains that the AM blocks, made in polycarbonate on FRC East's Stratasys Fortus 400mc and 900mc AM machines, enabled forming of stainless steel Z- and L-shaped metal doublers that were subsequently mechanically fastened, on board the ship, to splice a new portion of the frame that replaced the damaged portion of the frame (see images above). "The combination of the CAD solid model geometry and software, our tool designers, our AM machines and a dedicated workforce enabled a one-week total turnaround of the parts needed for this repair, which is pretty remarkable." A link to a YouTube video of the Harrier jet's hard landing is provided in "Learn More," on p. 31. Forming Fixtures These polycarbonate tooling blocks, produced on a Stratasys (Eden Prairie, MN, US) FDM machine, were printed in one day and used to form stainless steel repair doublers to repair a damaged frame within the nose cone of an AV-8B Harrier jet fghter. Source | NAVAIR Trim Tools When Aurora Flight Sciences (Manassas, VA, US) produced a series of female bulkhead tools, Stratasys (Eden Prairie, MN, US) simply printed lightweight trim tools (router templates) like this one for each bulkhead version, in a matter of a days, to expedite the trimming process. Doublers for nose repair This CAD drawing shows how the shaped metal doublers were fastened for the AV-8B Harrier nose cone frame repair. Source | NAVAIR CY133.7 FORMER -2004 STRAPS -2005 'C' STRAPS SKIN -2001 'Z' ANGLE DONOR CY 133.7 FORMER