CompositesWorld
Issue link: https://cw.epubxp.com/i/576646
OCTOBER 2015 4 CompositesWorld FROM THE EDITOR » October is CAMX month, and we here at CW are gearing up for the show, Oct. 26-29, at the Dallas Convention Center in Dallas, TX, US. We'll have a booth there, and we're publishing the CAMX Show Daily newspaper on site. Preparatory to the show, I was given a chance to conduct a Q&A; with this year's CAMX keynote speaker, Dr. Gary Smyth, executive director of Global Research and Development at General Motors (GM, Detroit, MI, US). Doing a Q&A; with a high-level corporate executive can be an uncertain proposition; some in this position hew so closely to the company line that getting meaningful and interesting answers can be a challenge. However, it's just as likely that a Q&A; will elicit illuminating and informative feedback that actually carries weight. Dr. Smyth, I'm happy to report, falls into the latter category. I don't have room here to record all he said. You can fnd the entire Q&A; on the CW Web site: short.compositesworld.com/ GarySmyth. What I can do is share with you some comments he made that elucidated the role composites will play in automotive manufacturing. First, if you are a regular reader of this column, you know that I have expressed concern that the composites industry, in general, is not well suited to meet the rigorous demands of the automotive supply chain, and I have questioned where composites fabricators will ft in the tier channel should automakers decide to more seri- ously work composites into cars and trucks. So, my question on this topic for Dr. Smyth was: Te composites industry does not have a history of providing high-volume, just- in-time (JIT) manufacturing services. If GM increases composites use, how will it cope with this challenge? Dr. Smyth's reply: "Tis is a signifcant issue and compounded by the complexity of the composites value chain. In the metal world, we buy sheet metal and stamp it into a part or, in some cases, buy a pre-made assembly. In the composites world, there can be a resin supplier, a fber supplier, a molder, and then a component assembler or fnisher/painter. Tis makes it very dif- cult to manage the whole value chain. One approach would be to bring the technology in-house; another is to closely partner in the plant, much as we do for the paint shop today. What is clear is that to enable true high-volume implementation, the right decisions need to be made early in part and process design to optimize material use and minimize manufacturing issues." I added the italics in Dr. Smyth's answer because I think that sentence captures very nicely some of the concerns automakers have when they look at the composites industry: Complexity, uncer- tainty, multiple materials. And given this uncertainty, it's fair then to ask: What advice do you have for composites fabricators who seek greater involvement in the automotive supply chain? Dr. Smyth's reply: ".... I would suggest working with Global Purchasing and Supply Chain to introduce your capability and then become part of the bidding process on future components. You should also reach out to technical leaders so they are aware of your capa- bility. One key to getting GM's attention is to clearly communicate the value or uniqueness that you bring as a supplier and to quantify that value. Tis often is done through a well-described case study for components you have produced for other industries or OEMs where you demonstrated improved performance or lower cost or better global reach." Again, I added the italics, which get at the crux of the issue for composites, which is that they must earn their way onto cars. Te automaking business model is simple: Make high-quality, safe vehicles for as little money as possible. Materials selection is, in the end, a meritocracy, and composites fabricators must prove the value their products have. Tis is easier said than done, but if it were easy, everyone would be doing it. However, it is doable. To get started, I encourage you to show up at CAMX, hear what Dr. Smyth has to say, and put to him a few questions of your own. Materials selection for automotive is, in the end, a meritocracy. JEFF SLOAN — Editor- In- Chief